Dry fire P64
Dry fire P64
Does dry firing the p64 do the gun any damage?
Dry fire P64
Dry firing in general is not good for guns. If possible you should use snap caps. It is not as bad for a P-64 as it would be for something with a brittle firing pin like a CZ-52. Since you cannot get P-64 parts, I would not dry fire a lot of times. I know people who have dry fired a lot of times and had no firing pin damage, you however might not be one of those.
-
- Veteran member
- Posts: 650
- Joined: November 19th, 2006, 8:28 pm
- Location: michigan, down the river
Dry fire P64
We have seen some of the safety barrels fail from being possibly over heat treated and brittle, cracking from dry firing.
Dry fire P64
Since 9 X 18 snap caps are not easy to find, consider what I did - put a cigarette filter under the hammer and dry fire until either the filter or your finger needs replacement (LOL) - "Ivan"
-
- Senior member
- Posts: 217
- Joined: March 24th, 2007, 7:50 am
- Location: SW Ohio
Dry fire P64
Snap caps will work well for limiting firing pin movement but will do nothing to protect the safety. The P-64 examples I've seen have inertia firing pins. The hammer impact on the safety is the same chamber loaded or not.
-
- Junior member
- Posts: 19
- Joined: May 1st, 2009, 9:20 pm
- Location: Conway, AR
Dry fire P64
I use a small piece of leather under the hammer...
Dry fire P64
jbailey wrote:Since 9 X 18 snap caps are not easy to find, consider what I did - put a cigarette filter under the hammer and dry fire until either the filter or your finger needs replacement (LOL) - "Ivan"
Great idea! They work well for ear plugs on the range in a pinch.
- kilogulf59
- Member
- Posts: 51
- Joined: March 4th, 2008, 6:03 pm
- Location: Juneau County Wisconsin
- Contact:
Dry fire P64
Once there's a dimple in there it is protecting nothing. If you can, get a piece of Delrin (Polyoxymethylene or POM ) and press it into the primer well. If you know someone in the machine tool trades (if there's any left that is) ask them and they may be able to make up a few for you.
Dry fire P64
I've made my own snap caps for 9x18. I pulled the bullet head, dumped the powder and de primed the case. Primed the case with a trimmed pencil eraser and reseated bullet. They seem to work pretty good.
Dry fire P64
My regular 9mm snap caps work just fine.
Re: Dry fire P64
Amazon.com has snap caps. Just time in 9mm makarov and there will be snap caps for i think around $15-$20, not sure.
Re: Dry fire P64
Your right, the safety needs protection as well as the firing pin...donnerwetter58 wrote:Snap caps will work well for limiting firing pin movement but will do nothing to protect the safety. The P-64 examples I've seen have inertia firing pins. The hammer impact on the safety is the same chamber loaded or not.
- fully machined
- Member
- Posts: 162
- Joined: August 14th, 2011, 11:14 pm
Re: Dry fire P64
I removed the firing pin and spring and reassembled with the complete safety assembly. Doubled actioned about twenty times with each hand, rest and then do again. About 100 or so double action dry fires. This made my safety loosen up and helped the double action feel after a clean and lube.
Re: Dry fire P64
can you post instructions on how you did that? Is there ANY harm that can result from this?
Thanks,
E.
-Why can't I find a Hoppe's-scented candle?
E.
-Why can't I find a Hoppe's-scented candle?