Page 2 of 4

Re: Polish Iron V05 grips, road testing

Posted: July 19th, 2017, 2:18 pm
by OG17
They will to some extent.

Re: Polish Iron V05 grips, road testing

Posted: July 19th, 2017, 11:08 pm
by Ketchman
yes a little, the most increase is across the back of the grip which has a small increase in width but that small increase is a huge help in taming recoil.

Re: Polish Iron V05 grips, road testing

Posted: August 7th, 2017, 7:49 pm
by Netspec
I like the grip/holster combo!

Re: Polish Iron V05 grips, road testing

Posted: August 7th, 2017, 8:57 pm
by Ketchman
Thanks. I myself like them very much too.

Re: Polish Iron V05 grips, road testing

Posted: August 7th, 2017, 9:38 pm
by Ketchman
Update:
Since my initial review I have carried this setup quite a bit more and I stil think this setup is better than sliced bread. The grips have help up extremly well, no warping, cracking or discoloration and still tames recoil well. And the holster has held up very well also. It has broken in nicely and yet still grips the gun quite well. The leathers finish has held up pretty well to sweat, which happens kinda often here in Wyoming in the summer. And the rig disappears under a T shirt or lightweight short sleeved button down.
All in all, between the V05 grips of PolishIron's and the Outbags IWB holster I have to say I have a pretty solid carry combo.

Re: Polish Iron V05 grips, road testing

Posted: August 8th, 2017, 9:28 am
by Netspec
"the V05 grips of PolishIron's and the Outbags IWB holster I have to say I have a pretty solid carry combo"

P-64's on its way, along with Hammer and recoil springs. Just need to order this holster and a belt!

Re: Polish Iron V05 grips, road testing

Posted: August 21st, 2017, 10:11 am
by Netspec
Ketchman,

Is there a brand of CC belt you'd recommend?

Re: Polish Iron V05 grips, road testing

Posted: August 21st, 2017, 8:26 pm
by Ketchman
Not specifically just make sure it is plenty stiff, like double thick cowhide or has a stiffener in it. Also make sure it is wide enough, a stiff belt that is only 1" wide will not have enough surface to distribute weight and tension over to be comfortable. Mine is extra thick cowhide and is 1 1/2" thick and sometimes with my heaviest EDC's that is not wide enough to be comfortable for long long periods. Make sure the buckle is sturdy as it will have to endure quite a bit of stress. The flexible fabric military belts are not good enough in my opinion unless they have been specially stiffened with plastic or steel inserts to make them stiff enough. But as far as a specific type, no, carry belts are as person specific as holster type and carry location preference, it is different for everyone. And you will go through a few before you find what works for you. Try looking at holster makers websites and get some ideas and sometimes you can find some at a gunshow where you can check them out before you buy. Don't depend on a Walmart or Costco belt.
I hope this helps.

Re: Polish Iron V05 grips, road testing

Posted: August 23rd, 2017, 11:46 am
by Netspec
Thanks Ketchman!

Re: Polish Iron V05 grips, road testing

Posted: August 23rd, 2017, 2:53 pm
by Ketchman
No problem. I hope I was able to help you.

Re: Polish Iron V05 grips, road testing

Posted: March 1st, 2018, 3:59 pm
by dmorris150
Just installed Russ's grips and extended mag release.wow what a diffrence they fit my hand like a glove.No more death grip on the gun,no more slide bite and fumbling to release the mag.I shot 200 rds of my reloads and 50 rds of critical defense yesterday at the range.This p64 is now going to be my every day carry.

Re: Polish Iron V05 grips, road testing

Posted: March 19th, 2018, 12:13 am
by Cyndicalist
I just bought the grips, I can't afford the extended release for a while. Is there any reason I absolutely need the extended release with the grips?

Re: Polish Iron V05 grips, road testing

Posted: March 19th, 2018, 12:21 am
by Ketchman
No., You should have no problems using the oem mag release with Russ's grips.

Re: Polish Iron V05 grips, road testing

Posted: March 19th, 2018, 1:32 am
by snailman153624
Walmart actually has a decent wide genuine leather belt, I think it was either Wrangler or Levis. Around $17, sturdy nickel-plated buckle, good thickness.

Re: Polish Iron V05 grips, road testing

Posted: March 19th, 2018, 2:00 pm
by Cyndicalist
Ketchman wrote: March 19th, 2018, 12:21 am No., You should have no problems using the oem mag release with Russ's grips.
Thanks sir - much appreciated. I am a new P64 owner and newish to the boards. Been lurking, decided that since I took the plunge to actually join. I am incredibly impressed with the community here.

Trying to figure out what, if any, spare parts I should buy. But the grip and extended release came highly recommended.